Skip to content
KokopelliRiver Notes
Raft crew in helmets running a class III rapid
Running a class III rapid. Photo: NPS Photo, Public domain, via Wikimedia Commons

Gear · safety

Helmets for packrafting

You sit low in a packraft, and in a swim on a rocky river your head is exposed. When to wear a water helmet, which label to look for and how to make sure it fits.

Last checked November 2026

Most packrafters skip the helmet on a calm lake or a slow, sandy river. Rocky water is different. A swimmer in a rapid tries to stay feet-first, but the current tumbles people, and heads hit rocks. Helmets are standard on Class II and harder water and sensible on any shallow, rocky run.

The packraft itself adds to the case. You sit on the floor with your head only a couple of feet above the water, so a flip puts your head near the riverbed almost at once. A short, light boat also gets surfed, spun and flipped more easily than a raft. And because packrafts reach places other boats don't, a head injury often happens far from a road. So the point where a helmet makes sense comes earlier in a packraft than many new paddlers expect, even if you still leave it off on most flat floats.

When to wear one

  • Any rapid of Class II or above, especially in rocky riverbeds.
  • Shallow, bouncy rivers where a flip means hitting the bottom.
  • Canyons and gorges where walls and undercuts are close.
  • Any time you use thigh straps or a spray deck and might roll.
  • Ice-cold water where a head knock could mean a short swim turns long.

If you are unsure, wear it rather than leaving it strapped to the pack. The guide to river difficulty classes explains the grading.

Two situations catch people out. The first is the "easy" river at low water, where a Class I run turns into a rock garden and a flip lands you on cobbles in a foot of water. The second is the long flat trip with one or two rapids in the middle. People leave the helmet buried in the pack for those trips and then run the rapids without it. Clip it to the outside of your pack or under the bow straps where you can grab it at the scout. Learning to read whitewater from the bank helps you spot which drops deserve it.

What makes a water helmet different

Water helmets drain and float, survive repeated soaking, and protect the back and sides of the head as well as the top. In Europe, helmets for canoeing and whitewater sports are tested to the EN 1385 standard, and many helmets sold in the US carry that marking too. A bike helmet is designed mostly for a single hard impact from above and to the front, with large vents that do little against a rock to the temple. A climbing helmet protects against falling objects. Either will do on easy water, but on real rapids you want a helmet made for paddling.

Standards and labels to check

There is no US federal safety standard written specifically for paddling helmets, the way there is for bicycle helmets. In practice the label to look for is EN 1385, the European standard for helmets used in canoeing and whitewater sports. The current edition is EN 1385:2012, which replaced the 1997 version. Helmets that meet it carry the standard number on a label inside the shell, usually alongside the CE mark, the size range and the date of manufacture.

A few details of the standard affect how you use the helmet:

  • It covers helmets for general paddling on whitewater, with and without drain holes in the shell.
  • Its scope excludes extreme whitewater such as running high waterfalls, where impacts are harder than the test assumes.
  • It sets no performance requirements for visors, chin guards or face guards. A face guard on an EN 1385 helmet hasn't been tested by that standard.
  • Its protection levels are set around the main paddling risk it was written for: a blow to the head that stuns a swimmer, who then drowns.

Bike helmets sold in the US are certified to the Consumer Product Safety Commission bicycle helmet standard, and climbing helmets to UIAA or EN 12492. Each of those tests a different kind of impact. A few multi-sport helmets are certified to more than one, which is handy for bikerafting trips where you want to carry only one lid.

Half shell, full-cut or full-face?

StyleCoverageGood forTrade-offs
Half-cutTop and back of head, ears openEasy whitewater, hot weather, better hearingLess protection at the temples and ears
Full-cutCovers ears and lower back of headRocky creeks and harder rapidsWarmer, can muffle shouts and whistles
Full-cut with face guardAdds a guard over the faceSteep creeks, shallow dropsHeavier, bulkier to pack, face guard not covered by EN 1385

Most packrafters on Class II and III do well with a half-cut or full-cut helmet. On a river trip you rely on hearing whistle signals and shouted calls, and full-cut ear covers dull them a little. Some full-cut models have ear pieces you can remove for summer. Full-face helmets make sense on low-volume creeks where a face-first hit on rock is a real possibility, and they add weight and bulk that most backcountry packrafters would rather not carry.

Fit check

A water helmet should sit low on your forehead, about a finger's width above your eyebrows. With the chin strap snug, push the helmet back and forth and side to side. It should move your scalp with it, not slide around on top. Tilt your head forward: the helmet should not tip down over your eyes. Try it with whatever you wear underneath on cold days, such as a neoprene cap, and adjust the pads or the retention system to suit.

Five-step fit test

  1. Measure your head circumference just above the eyebrows and ears, and pick the size whose range includes it.
  2. Put the helmet on level, front edge about one finger above your brows, and tighten the dial or pads until it feels evenly snug with no pressure points.
  3. Buckle the chin strap so you can fit only one or two fingers between strap and chin, and set the side straps to form a V just below each ear.
  4. Grab the helmet and try to roll it backward off your head, then forward over your eyes. It should not expose your forehead or cover your eyes.
  5. Shake your head hard, then wear it for 15 minutes. Any hot spot that appears now will be worse after a day on the river.

Do the test wet if you can. Some liners compress or loosen when soaked, and a helmet that feels firm in the store can rotate once the pads are full of water. If you will wear a hood or skull cap on cold rivers, test with it on.

Common mistakes

  • Wearing the helmet tipped back on the head. It looks relaxed and leaves your forehead open.
  • Leaving the chin strap loose for comfort. A current can pull a loose helmet back and the strap can then press on your throat.
  • Sizing up so a warm hat fits underneath, then wearing it without the hat in summer.
  • Using a bike helmet on a rocky Class III run because it was already on the boat.
  • Packing the helmet under heavy gear so the shell deforms or the foam crushes.

Care and replacement

Rinse the helmet in fresh water after a trip and let it dry out of direct sun. UV and heat weaken plastic shells over time. Replace a helmet after a hard impact, even if it looks fine, and replace it if the shell is cracked, the foam is crushed or the straps are frayed. Do not paint the shell or add stickers that use solvents unless the maker says it is safe.

Makers give their own service life, usually counted from the manufacture date on the label rather than from when you bought it, so follow the instructions that came with the helmet. Store it somewhere cool and dark between seasons, and don't leave it on a car dashboard or in a hot trunk.

Fit it into your system

A helmet works with a well-fitted life jacket, outfitting like thigh straps, and good cold-water layers. On a bikerafting trip, some paddlers use their bike helmet for flatwater crossings and carry a water helmet for rapids. See the gear overview for the rest.

If you run a spray deck and are learning to roll, wear the helmet every time you're on moving water. In snowmelt season, a head knock combined with cold shock is a bad pairing; the cold-water safety guide explains why the first minutes in the water matter so much. And whatever you wear on your head, the self-rescue guide covers how to swim a rapid with your head and feet in the safest position.

FAQ

Can I use my bike helmet for packrafting?

On flatwater and easy rivers it's better than nothing. On rocky rapids, a water helmet is the better choice because it drains, floats, covers more of the side and back of the head, and is tested for paddling.

Do helmets float?

Most water helmets float, but don't count on a helmet to keep you up. Your life jacket does that job.

Is a full-face helmet worth it for packrafting?

Only for steep, shallow creeks where you might hit your face. For most Class II and III rivers a half-cut or full-cut helmet is enough, and lighter to carry.

How do I know if my helmet needs replacing?

Replace it after any hard impact, if the shell is cracked, the foam is dented or crushed, or the straps are frayed, and once it passes the maker's stated service life.

Should kids wear helmets in a packraft?

Yes, on any moving water, and the fit matters even more because small heads move inside an oversized shell. Use a helmet sized for children with its own fit test.