Skip to content
KokopelliRiver Notes
A red packraft pulled up on river gravel under a storm sky
Packraft on the Anaktuvuk River, North Slope, Alaska. Photo: Paxson Woelber, CC BY-SA 3.0, via Wikimedia Commons

Boats · materials

Fabrics and construction

Two packrafts with the same shape can wear out years apart, depending on the fabric and how the panels are joined. A spec sheet tells you most of what you need, once you know how to read it.

Last checked November 2026

Packraft fabric has to hold air, survive scrapes on rock and still fold small. Most boats use a woven nylon base coated with a waterproof polymer, and the choices made at each layer affect weight and durability.

The base cloth gives the boat its strength, the coating makes it airtight, and the seams hold the panels together. Heavier choices at any of those layers buy toughness at the cost of weight, and the coating and seam type also decide how you patch the boat later.

The base cloth

Nylon is the most common base fabric because it is strong for its weight and folds well. Polyester shows up in some boats and accessories. The fabric weight is usually given in denier, a measure of the yarn thickness. Higher numbers mean thicker yarns and, broadly, more abrasion resistance and more weight.

Technically, denier is a unit of linear density: the weight in grams of 9,000 meters of a single yarn. So a 420D yarn weighs twice as much per length as a 210D yarn. Denier describes the thread, not the finished fabric, which is why two "210D" fabrics can feel quite different in the hand.

Weave density, coating thickness and the base material matter as much as the denier number. A well-coated 210D fabric can outlast a poorly coated heavier cloth.

Other numbers on a spec sheet

  • Fabric weight per area (ounces per square yard or grams per square meter) includes the coating, so it tells you more about the finished material than denier alone.
  • Thread count or weave type (plain, ripstop) affects tear resistance. Ripstop has a grid of heavier yarns that stops a small tear from running.
  • Total boat weight is the number that matters on your back, and it includes the floor, seat, valves and any zipper.

If a maker lists only denier, ask for the coated fabric weight, which compares better between brands.

Coatings

TPU (thermoplastic polyurethane) is the most widespread coating in modern packrafts. It holds air well, stays supple in the cold and can be heat-welded.

PU (polyurethane) coatings, applied as a liquid and cured rather than laminated as a film, are lighter and cheaper. They show up on some ultralight boats and on accessories such as dry bags and deck fabric. They can be thinner and are often glued rather than welded.

PVC is cheaper and very tough, but it is heavier and stiffer and cracks more easily in cold weather. It is common in budget inflatables but rarely used in serious packrafts.

Hypalon (CSM) and neoprene-type rubber coatings show up on heavier rafts and some inflatable kayaks. They last well but are heavy, and seams have to be glued.

Coatings can be on one or both sides. A double-coated fabric typically resists abrasion and holds air better than a single-coated one. On many packrafts the coating faces inward on the tubes, to hold air, while the floor has a heavier coating on the outside to take wear.

Fabric and coating compared

MaterialTypical use in packraftsWeightAbrasion and punctureCold weatherJoining
Light nylon with TPUUltralight tubesLowestFair; cut by sharp rockStays flexibleWelded
Mid-weight nylon with TPUGeneral-purpose tubesModerateGoodStays flexibleWelded
Heavy nylon with TPUFloors, whitewater boatsHigherVery goodStays flexibleWelded or glued
Nylon with PUSome light boats, decks, bagsLowFairGenerally fineUsually glued
PVCBudget inflatablesHighGoodStiffens, can crackWelded or glued
Hypalon or neoprene rubberHeavy rafts and IKsHighVery goodGoodGlued

Treat the table as a rough guide. Coating thickness and quality vary a lot within each row.

What coatings mean in the field

  • On a cold morning, a TPU boat rolls out and inflates easily. A PVC inflatable left out overnight can be stiff and harder to pack.
  • On gravel bars, coating wears off the floor first. Once the base weave shows through, that area will start to seep. A heavier floor coating buys you more drags before that happens.
  • In hot sun, all coatings suffer slowly from UV, and the air inside expands. Welded TPU seams handle heat better than many glued seams.
  • In repairs, TPU accepts heat or a compatible urethane glue. PVC and rubber coatings each need their own adhesives, and the wrong glue simply peels off.

Seams

MethodHow it worksProsCons
Heat or RF weldingCoating melted together under heat or radio frequencyStrong, consistent, no glueNeeds weldable coating, factory equipment
GluedPanels bonded with adhesiveField-repairable, works on any coatingDepends on glue and skill, can creep with heat
TapedSeam tape welded or glued over the joinExtra strength and air sealingAdds weight

Many packrafts combine methods: welded tube seams with a glued floor, or welded seams finished with tape on the inside. Fittings such as D-rings, valves and thigh strap anchors are usually welded or glued on patches.

How to judge seams on a boat in front of you

  1. Look along each seam in good light. A welded seam should be an even band with no wrinkles, gaps or bubbles.
  2. Check glued seams for adhesive squeezing out unevenly or edges that you can lift with a fingernail.
  3. Inspect where seams meet each other, such as where the tube joins the floor at the bow. Those junctions take the most stress.
  4. Look at fitting patches. A patch that has started to lift at one edge will keep lifting under load.
  5. Inflate the boat firmly and brush soapy water along the seams. A steady stream of tiny bubbles marks a leak.

Floors and tubes are built differently

The floor takes the beating. It slides over gravel, gets dragged across sandbars and pressed onto rocks by your weight. Tube fabric mostly deals with air pressure, sun and the odd scrape against a canyon wall, so many boats use a much heavier fabric on the floor than on the tubes.

Rocky, shallow rivers chew floors fastest. On a low-water float like the Escalante River, with lots of wading and dragging, the floor fabric is the first thing to look at on a spec sheet. If you run creeks, a whitewater packraft usually has tougher fabric at the bow and stern, where rocks hit first. Some designs add a second layer or a separate wear patch under the seat.

Self-bailing floors use holes or a separate inflatable floor, and the construction around those openings is another place to check; the self-bailing floors guide covers how they are built.

What this means when choosing a boat

Shallow, rocky rivers chew floors, so a heavier floor fabric is worth the weight if you will be dragging the boat over gravel. Light tube fabric is fine on lakes, but sharp rock and branches can cut it; the page on minimal backcountry boats covers that trade-off.

A worked example

Say you are choosing between two boats of the same shape. One has light tubes and a mid-weight floor, and weighs a little less. The other has mid-weight tubes and a heavy floor. Ask yourself three things:

  • How far will you carry it? If most trips start with a long hike, the lighter boat earns its place.
  • What will the floor touch? Sandy desert rivers and gravel bars favor the heavier floor.
  • How careful are you? A light boat lasts years if you lift it over rocks and pick your landings, and wears through quickly if you drag it every day.

A paddler who hikes far to alpine lakes picks the first boat. A paddler running shallow desert rivers from a car picks the second. Someone doing both often accepts the heavier boat and saves weight elsewhere in the pack. For a wider view of boat types, the packraft and inflatable kayak comparison puts packraft materials next to other inflatables.

On a used boat, look at the seams as closely as the fabric. Lifting edges and bubbles are the warning signs, and the second-hand inspection guide explains how to check them.

Air pressure and the fabric

Packrafts run at low pressure compared with many inflatables, and the fabric and seams are designed around that. Over-inflating with a pump stresses seams for no real gain in stiffness. Most paddlers fill the boat with an inflation bag and top up by mouth, then add a little more after the cold river water shrinks the air. The guide to inflating a packraft walks through that routine, and the inflation bag and pump notes cover the gear.

Field repair

Coating type decides which glues and patches work. TPU boats typically take TPU patches with a compatible urethane adhesive. Carry the right kit for your boat; the field repair guide walks through patching.

Before a trip, find out from the maker what fabric your tubes and floor use and what adhesive they recommend. Keep a piece of matching patch fabric in your kit, cut with rounded corners so it does not peel. Clean and dry the area before you glue, and give the adhesive the curing time it asks for, even if that means a long lunch.

For how each fabric layer sits on the boat, see the packraft parts page, or return to the main boats page.

Is a higher denier fabric always tougher?

Not always. Denier measures yarn thickness. Weave, coating thickness and coating quality matter as much, so a well-coated lighter fabric can outlast a poorly coated heavier one.

Why do most packrafts use TPU instead of PVC?

TPU is lighter, stays flexible in the cold and can be welded. PVC is heavier and stiffer, and it can crack in low temperatures.

Are welded seams better than glued seams?

Welded seams are consistent and do not rely on glue, so they handle heat well. Glued seams can be strong too and are easier to repair in the field. Many boats use both.

Can I use any vinyl patch kit on a TPU packraft?

Use a TPU patch and an adhesive the boat maker recommends. Glue made for other coatings may not bond properly.

Why is the floor fabric heavier than the tubes?

The floor scrapes over rocks and gravel and carries your weight, so it wears much faster than the tubes.