Skip to content
KokopelliRiver Notes
A red packraft pulled up on river gravel under a storm sky
Packraft on the Anaktuvuk River, North Slope, Alaska. Photo: Paxson Woelber, CC BY-SA 3.0, via Wikimedia Commons

Skills · boat care

Packraft care and storage

Packraft fabric is tough, but sand, sun, salt and damp storage wear it out faster than rocks do. A few minutes of care after each trip adds years to a boat.

Last checked November 2026

Most packrafts are made of nylon fabric coated with urethane (TPU) or similar, with welded or glued seams. That construction handles impact well. It does not like long hours of direct sun, grit trapped in folds, salt crystals in zipper teeth or being packed away wet. The materials themselves are covered under fabrics and construction.

Most of the wear on a boat comes between trips: a wet boat left rolled in a car for a week, a zipper closed over sand, a boat stored in a hot garage all summer. The fixes are simple, and the whole routine adds maybe twenty minutes to the end of a trip.

After every trip

  1. Rinse the boat with fresh water, inside and out, especially after salt water or silty desert rivers.
  2. Flush sand from the inside of cargo tubes if your boat has them.
  3. Wipe or rinse the spray deck, seat and backrest.
  4. Dry the boat completely in shade, inflated or loosely open, before packing it.
  5. Rinse and dry the inflation bag, which collects grit and moisture too.

On a multi-day trip, rinse what you can and dry the boat on shore at lunch or in camp, turning it upside down so the floor dries too.

What to clean with

Plain fresh water does most of the work. For mud, sunscreen smears and grime, use a soft sponge or cloth with a mild, non-detergent soap, then rinse well. Skip solvents, bleach, abrasive pads and strong household cleaners, which can damage coatings and adhesives. If a boat smells of mildew, a wash with mild soap and a long dry in the shade usually fixes it; check the maker's care notes before you try anything stronger.

Silt from desert rivers is finer than it looks. It settles in seams, under the seat and inside cargo tubes, and it acts like sandpaper every time the boat flexes. A garden hose and a few minutes of flushing at home is worth doing even when the boat looks clean.

Care on the river

Most damage on long trips comes from the way the boat is handled out of the water.

  • Carry the boat over rocky landings rather than dragging it. Two hands on the grab loops or bow line is enough for most boats.
  • Clear sharp sticks, cactus and rocks before setting the boat down in camp.
  • Keep the boat in shade at lunch, or flip it so the floor faces the sun instead of the tubes.
  • Rinse sand off the zipper before you close it, even if that means dunking it in the river first.
  • Tie the boat up at night, upstream end high, so wind or rising water can't move it.
  • Check the boat every evening for new scuffs, and patch anything worn through while the boat is dry and you have time.

Paddles and PFDs need care too. Rinse sand out of the paddle joints so the ferrules keep locking cleanly, and dry your life jacket in the shade, since foam and fabric break down in long sun.

Sun and heat

Ultraviolet light breaks down fabric coatings over time. A boat left inflated on a sunny beach all afternoon also heats up, and the air inside expands. Keep the boat in shade when you can, release a little air if it sits in hot sun and do not leave it lying out for days at a time. A light-colored boat heats less than a dark one.

The reverse happens in the morning. Air that was firm at noon contracts in cold river water and a cool dawn, and the boat goes soft. Top it up after it has sat in the water for a few minutes rather than pumping it hard on a hot beach. The inflation bags and pumps page covers top-up valves and tools.

Some makers approve a UV protectant spray for their fabrics; others say it is unnecessary or advise against particular products. Read the care notes for your boat before applying anything to the coating.

Zippers and valves

PartCare
Waterproof cargo zipperRinse sand out after every trip, lubricate the teeth with the zipper maker's recommended lubricant, never force it closed over grit
Main inflation valveKeep the threads and rubber seal free of sand, store with the valve open
Top-up valveCheck that the cap seals; replace a cracked cap or missing O-ring
Spray deck and fastenersRinse, check stitching and velcro, replace frayed shock cord

Of all the parts, the waterproof zipper suffers most from neglect. Sand caught in the teeth can scratch the seal so it no longer holds air. Close the zipper slowly, with the slider moving freely, and store it slightly open. The page on cargo zippers goes into this in more depth.

Valves are simpler but easy to forget. Before each trip, unscrew the main valve cap, look at the seal for sand, cracks or a twisted O-ring, and screw it back in by hand. Never use tools to tighten a valve, because overtightening can distort the seat and make it leak.

Transport and travel

A packraft spends a lot of time in packs, car trunks and airline luggage, and that is where many small holes start.

  • Roll or fold the boat around soft gear, not around paddle blades, tent stakes or a stove.
  • Put a stuff sack or pack liner between the boat and anything with an edge.
  • In a car, keep it off hot metal floors and away from tools and bike parts.
  • For flights, deflate fully, fold loosely and pad the valve area.
  • In cold weather, coated fabrics stiffen. Let a frozen boat warm up before unrolling it hard, and avoid sharp folds while it is cold.

If you carry the boat on a bike, the bikerafting setup page covers how to strap it so it doesn't rub on the frame.

Long-term storage

Store the boat clean and fully dry, in a cool, dark, dry place. The best options, in order:

  • Lightly inflated or loosely folded under a bed or on a shelf.
  • Loosely rolled, without sharp creases, in a breathable bag.
  • Tightly rolled in a stuff sack only for short periods or travel.

Avoid attics and car trunks, where heat builds up, and damp basements, where mildew grows. Keep it away from rodents, which will chew fabric. If you notice a musty smell, wash the boat with mild soap and water, rinse it thoroughly and dry it completely.

Off-season checklist

ItemBefore storingNotes
BoatWashed, fully dry, valves open, zipper slightly openChange the fold lines now and then if it is stored folded
Spray deck and seatRinsed and dry, stored looselyCheck velcro and shock cord
PaddleTaken apart, rinsed, joints dryStore pieces together so none go missing
Inflation bagRinsed, dry, turned inside out to airGrit inside it ends up in the valve next season
DrysuitWashed per maker's notes, hung loosely, zippers openKeep latex gaskets away from heat, sun and petroleum products
PFDRinsed, dried, hung or laid flatCheck foam for compression and fabric for fading

The drysuits and layering page has more on caring for gaskets and zippers on your paddling clothes.

Pre-season check

A full check takes an evening and catches most problems while you still have time to fix them.

  1. Unroll the boat and look over the whole surface in good light for scuffs, worn coating, delamination and soft seams.
  2. Inflate it fully with the valve seal checked, and leave it overnight somewhere with a steady temperature.
  3. If it has softened, brush soapy water on the valves first, then along the seams and any patches, and watch for bubbles.
  4. Open and close the cargo zipper slowly, clean it and lubricate it as the maker recommends.
  5. Check grab loops, tie-down points and thigh-strap anchors by pulling on them firmly.
  6. Restock the repair kit, since adhesive has a shelf life and patches go missing.
  7. Assemble the paddle, flex the joints and look for cracks in the blades.

Small repairs

Small abrasions, pinholes and worn spots are easy to fix before they turn into bigger problems. Clean the area, use a patch and adhesive suited to the boat's coating and let it cure fully. The packraft repair page has step-by-step instructions. If you are checking a secondhand boat, the guide to buying a used packraft lists the signs of neglect to look for.

Before you repack the boat after a trip, wash off anything that came from another river, since care and cleaning overlap with stopping invasive species; the Leave No Trace notes explain the clean, drain, dry routine.

A well-kept boat inflates faster and holds air better, which ties straight back to the inflation routine. If you are renting, the same checks apply at pickup; the rental guide covers them. Find more boat-handling skills on the hub.

How should I store a packraft over winter?

Clean and fully dry, in a cool, dark, dry room, ideally lightly inflated or loosely folded with the valves open and the zipper slightly open. Avoid attics, car trunks and damp basements.

Can I store a packraft rolled up?

For short periods, yes. For months at a time, a loose fold or light inflation is better, because tight rolls leave hard creases that stress the coating.

How do I clean a packraft after a salt-water trip?

Rinse it inside and out with fresh water, flush any cargo tubes, rinse the zipper and valves, then dry it in shade before packing it away.

Does sun damage a packraft?

Long exposure to UV slowly breaks down coatings, and heat makes the air inside expand. Keep the boat in shade when you're not paddling.

Why is my packraft soft every morning?

Cold air contracts. A boat pumped firm in the afternoon sun will soften overnight and in cold water. Top it up once it has cooled, and check the valves if it keeps losing air.