Skip to content
KokopelliRiver Notes
A packraft rolled into its bag next to a bottle and an apple for scale
A packraft rolled for carrying, shown for scale. Photo: Esben~dewiki, CC BY-SA 4.0, via Wikimedia Commons

Boats · storage

Cargo zippers and in-tube storage

An airtight zipper in the side of the tube turns the inside of your packraft into a dry hold. It lowers the load and clears the bow, though the zipper needs regular cleaning and lube.

Last checked November 2026

The classic way to carry gear on a packraft is to strap your pack across the bow. It works, but a heavy pack raises the center of gravity, blocks your view and catches waves. In-tube storage moves that weight inside the boat's tubes, down low and out of the way.

How it works

A long airtight zipper is set into the tube, usually along the stern or one side. Before inflating, you open the zipper, slide gear into the tube in dry bags or stuff sacks, close the zipper fully and then inflate as normal. The gear sits inside the air chamber. The most widely known airtight zipper type in packrafts is the TIZIP, though other makers produce similar zippers.

When fully closed, the zipper holds air and keeps water out. It only seals if the slider is pushed all the way home and the teeth are clean, so treat it with more care than a dry bag roll-top.

What the zipper is made of

An airtight zipper is a coated, flexible band with interlocking teeth and a slider that presses the two halves together into a seal. The band is welded or glued into a reinforced opening in the tube fabric. Because the seal comes from the coating pressing together along its whole length, anything caught between the halves (a grain of sand, a hair, a thread from a stuff sack) can open a leak path. The packraft parts guide shows where the zipper usually sits relative to the valves and seat.

Where the gear actually goes

The stern tube, and on some boats the side tubes, become a long, narrow hold. Gear slides in from the zipper opening and gets pushed along toward the bow on each side. Once the boat is inflated, the air pressure presses the tube fabric around the bags and holds them in place. The total space is generous for clothing, sleeping gear and food, but long, rigid items and anything with sharp edges do not belong inside.

Benefits

Weight inside the tubes sits near the waterline, which makes the boat more stable in waves. With little or nothing on the bow you can see the river ahead, and the boat rides over waves more cleanly.

Gear in the tubes stays out of the wind and spray, and a flip will not tear it loose. You can also trim the boat by placing heavy items where they balance it best, front to back and side to side.

In whitewater, a boat with a big bow pack is harder to turn, slower to recover from a hit and more likely to flip end over end in a hole. With the load inside, the boat behaves much more like an empty one. That is one reason boats built for rapids often come with cargo zippers; the whitewater packraft page covers the other design features.

Drawbacks

DrawbackWhat it means in practice
Added weightThe zipper and reinforcement add some ounces
Extra part to maintainNeeds cleaning and occasional lube
AccessYou must deflate to reach gear
RepairA damaged zipper is harder to fix than a hole in a tube
CostBoats with zippers tend to cost more
Packing timeLoading tubes takes longer than strapping a pack to the bow

Because you must partly deflate the boat to get at anything inside, keep lunch, water, a rain jacket and your repair kit somewhere you can reach.

What to put inside and what to keep out

Gear you will not need until camp goes inside the tubes. Anything you might want on the water stays in the cockpit or on the bow.

Good in the tubesKeep in the cockpit or on deck
Sleeping bag and padWater bottle and snacks
Spare clothing, camp shoesRain shell and warm layer
Tent body and fly (poles out)Repair kit and spare valve parts
Food for later daysThrow bag, knife, whistle
Stove and fuel in a separate bagMap, phone, first aid kit

Pack soft items in long, thin dry bags. Even inside a closed tube, a zipper can leak a little, and water that gets in through a failed seal or a puncture will soak anything loose. Purpose-made tube bags exist, but any slim roll-top dry bag that slides in easily will work. Keep fuel canisters, tent poles, stakes and knives out of the tubes, or wrap them so nothing hard rubs against the inside of the tube fabric.

Loading the tubes

  1. Pack gear into long, narrow dry bags or stuff sacks so they slide in easily.
  2. Push each bag well along the tube, spreading the weight evenly left and right.
  3. Wipe the zipper teeth clean of sand and grit.
  4. Close the zipper fully, pushing the slider firmly into its end stop.
  5. Inflate and check for hissing at the zipper before launching.

Lay the deflated boat flat on a tarp or clean rock, zipper side up. Load heavy, dense items first and push them furthest forward along each side, then fill in behind with lighter, squashable gear. Leave the area right behind the zipper opening fairly clear, since gear jammed against the zipper puts strain on it once the tube is inflated. Some paddlers tie a short cord to the last bag in each tube so they can pull the load back out in one go at camp.

When you inflate, follow your usual routine from the inflation guide, but watch the zipper area as the tube firms up. If a bag bulges right against the zipper, let some air out, shift it and top up again.

Trimming the load

A boat with a heavy stern rides with its bow high and catches the wind. Move denser gear forward along the side tubes until the boat sits level with you in it. If the boat lists to one side, swap a bag across. In a tandem packraft the front paddler's weight already helps level the boat, so you need to move less gear forward.

Zipper care

Most problems come from grit and from forcing a stiff slider. Rinse the zipper in fresh water after sandy trips, and dry it before storing. Lubricate it with the product the zipper maker recommends. Never pull the slider with the tube inflated. The general storage routine in the packraft care guide covers the rest of the boat.

Cleaning and lubricating

Makers of boats with TIZIP-type zippers give much the same care advice. Clean the zipper with mild soap and fresh water, then let it dry. Apply the maker's lubricant sparingly with a cloth to the outer rubbery coating along the zipper, not to the teeth, and work it in until the slider runs smoothly. Wipe off the excess afterward, because leftover lube attracts sand and dirt. Avoid general-purpose greases, silicone sprays and wipes sold for other zipper types unless your boat's maker approves them.

  1. Open the zipper fully on a clean surface.
  2. Rinse grit out with fresh water, using a soft brush along the teeth if needed.
  3. Wash with a little mild soap and rinse again.
  4. Let it dry completely, out of direct sun.
  5. Apply a thin layer of the recommended lubricant to the coating with a cloth.
  6. Run the slider end to end a few times, then wipe away any excess.

Drying and storage

A zipper stored damp can rot or crack, and makers generally treat that as owner neglect rather than a warranty fault. After a trip, open the zipper and let the inside of the tube air out as well. If you have to drive home with a wet boat, pack it so the zipper sits on the outside of the roll, where it gets some air, and dry everything properly that evening. Follow your boat's manual on whether to store the zipper open or closed.

When things go wrong

SymptomLikely causeWhat to do
Hissing at the zipper after inflationSlider not fully home, or grit in the sealDeflate, clean, close firmly into the end stop, reinflate
Slider very stiffDry or dirty coatingClean and lubricate as above; do not force it
Slow leak along the bandWorn coating, damage or old lube with dirt in itClean and test with soapy water; contact the maker if it persists
Teeth separate behind the sliderDamaged slider or teethStop using the zipper; seek a professional repair
Wet gear after a tripLeaking seal or puncture in the tubeFind the leak before the next trip

A soapy water test works on zippers as on seams. Inflate the boat firmly, brush or spray soapy water along the closed zipper and watch for bubbles. The repair section covers patching the tube itself, but zipper replacement is usually a job for the boat's maker or a specialist repair shop.

Who it suits

Cargo zippers make the most sense for multi-day river trips, for bikerafting where the bow is already taken by the bike, and for whitewater trips where a bow pack would be a liability. For short day trips or lake crossings, a simple bow load is lighter and quicker. A self-bailer also pairs well with in-tube storage, since the cockpit stays wet.

If you are planning a first overnight trip and deciding what to bring, the trip planning notes help you work out the load before you work out where it goes. For the full range of designs, start from the packrafts hub page.

Can I open a cargo zipper while the boat is inflated?

No. Let the air out first. Pulling the slider under pressure strains the zipper and can damage the seal.

Will gear inside the tubes stay dry?

Usually, if the zipper is clean and fully closed. A puncture or a leaking seal can still let water in, so pack everything in dry bags anyway.

How often should I lubricate the zipper?

When the slider starts to feel stiff, and after cleaning it at the end of sandy or salty trips. Use the lubricant the zipper maker recommends.

Does in-tube storage make a packraft heavier?

The zipper and its reinforcement add a few ounces. On multi-day trips most paddlers accept that for the lower, steadier load.

Can a cargo zipper be fitted to an older boat?

Some makers and repair shops do retrofits, but it is a factory-type job that involves cutting the tube. Ask the boat's maker before you plan on it.